EMT Practice Test

1. Question Content...

---

Question1: Recently, your 2-node FAS8020 cluster was upgraded from ONTAP 8.3 to ONTAP 9.1. You have just added two FAS8060 nodes to the cluster. You have executed Config Advisor to verify your work. Config Advisor tells you that the cluster ports on the original two FAS8020 nodes have Flow Control set to FULL.
In this scenario, to what should the Flow Control setting on the FAS8020 ports be set?

Question2: Config Advisor reports that you have a single point of failure on a stack of shelves. After investigation, you have assigned the following ports to each stack:
stack 1 - ports 0a and 0b
stack 2 -ports 3a and 4b
stack 3 - ports 4a and 3b
In this scenario, which two changes would you make to the cabling to solve the problem? (Choose two.)

Question3: After an installation, your customer asks you if you have a solution or a product that can easily list all the elements of a running ONTAP cluster, and highlight the changed and new objects including IP addresses, subnets, IPspaces, SVMs, volumes, and LUNs. For easy modification the output should be a document or a spreadsheet. Your customer does not have any PowerShell or scripting knowledge.
In this scenario, which Windows PowerShell-based NetApp tool would help to extract this information?

Question4: You are preparing to install a new cluster at a customer site.
Which two concerns must you address with the customer in this scenario? (Choose two.)

Question5: You are going to add a node to an existing cluster but first you must gather the appropriate information for the new node's management LIF.
What two pieces of information is required to accomplish this task? (Choose two.)

Question6: A customer ordered two new DS224C shelves. The customer wants you to add these shelves to an existing stack which consists of two DS2246 shelves.
Which statement is true in this scenario?

Question7: You are dispatched to install a new cluster with six AFF A300 nodes. While running Config Advisor, you determine that there is a newer firmware version for 48 SSDs.
Which statement is correct in this scenario?

Question8: A customer has an ONTAP 9.1 8-node FAS8080 EX cluster. The cluster uses CN1610 cluster interconnect switches. The current workload runs NAS protocols. A business unit wants to add an additional workload that requires expanding the cluster by six AFF A300 nodes and use SAN protocols.
How would you advise the customer in this situation?

Question9: You finished the installation of a 2-node cluster and want to determine whether HA is configured correctly.
What are two ways to accomplish this task? (Choose two.)

Question10: Select the Exhibit tab.

You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.1 on a customer site.
Referring to the exhibit, which two statements describe what is required to get an HA cabled system?
(Choose two.)

Question11: You have created an aggregate with one RAID group on your ONTAP 9 cluster. Two disks have already failed and have not finished reconstructing.
What would protect you from a third disk failure while you are still reconstructing the two failed disks?

Question12: You have just replaced a FAS controller with a new controller and installed the appropriate licenses for the new FAS controller.
What are two ways to remove unused licenses in this situation? (Choose two.)

Question13: Without adding new cluster interconnect switches, you want to nondisruptively upgrade from FAS2554 controllers to FAS8200 controllers on an existing 2-node switchless cluster running ONTAP 9.1 software.
Which statement is correct in this scenario?

Question14: You just finished an AFF A300 installation with two DS224C disk shelves.
What are two ways to cable these disk shelves? (Choose two.)

Question15: You are asked to install an AFF A700 with two DS224C shelves fully populated. When you arrive, the customer asks you to install an additional shelf.
Which shelf would you add to this cluster?

Question16: You are configuring a new system with ONTAP 9.1. You created interface groups, VLANs, and a broadcast domain for the new ports on all the nodes of your cluster. During the configuration, you used an MTU value of 1500 for the broadcast domain and 9000 for the physical ports. The customer asks you to enable jumbo frames.
What should you do in this scenario?

Question17: You finished an ONTAP 9.1 installation using the information provided by the customer, but the NFS exports and CIFS shares cannot be accessed using the newly created data LIFs.
In this situation, which action should you perform before you leave the customer's site?

Question18: A customer has a stack of shelves with both DS4243 shelves and DS4246 shelves. The customer wants to replace the DS4243 shelves with new DS4246 shelves.
What would you advise the customer in this scenario?

Question19: You have a 4-node FAS8060 cluster. You are using the vol move command to relocate a volume from an aggregate on node 1 to an aggregate on node 4.
In this scenario, which network is used for the traffic being relocated?

Question20: You are asked to install a 2-node FAS2554 cluster running ONTAP 9.1. The controller arrived with ONTAP
9.0 installed.
In this scenario, which two tools would be used to complete this upgrade for this installation? (Choose two.)

Question21: To ensure that your customer's cluster is robust and operational, you need to be familiar with configuration best practices.
Which three practice rules should you always follow? (Choose three.)

Question22: A customer has a standard request for information regarding the installation, configuration, usage, and maintenance of his NetApp equipment.
What is the appropriate priority level to use when he opens a case?

Question23: You want to expand an existing FAS8060 switchless cluster running ONTAP 9.1 with an AFF A300 system.
Which action should you take to perform this task?

Question24: You were dispatched to add a DS224C to an existing HA pair that has a stack of DS4243 shelves with 1 TB drives and a stack of DS4246 shelves with 1 TB drives. The customer wants to make sure that ACP is cabled for all shelves.
Which two considerations should you advise the customer in this situation? (Choose two.)

Question25: Select the Exhibit tab.

You install a new FAS2552 HA using a DS2246 disk shelf and ONTAP 9.1 on a customer site.
Referring to the exhibit, which two statements describe what is required to get an HA cabled system?
(Choose two.)

Question26: What are two ways to obtain customer licenses for a new ONTAP system? (Choose two.)

Question27: Select the Exhibit tab.

You finished the installation of a new FAS8200 system. The customer wants to use FC and 10G Ethernet but only has the onboard UTA2 ports available.
Referring to the exhibit, which two sets of ports would the customer use? (Choose two.)

Question28: You have just added a new DS4246 shelf with 24 x 10 TB SATA HDDs to a single FAS2650 node as the first SATA shelf. You must keep two SATA spare disks on the shelf.
What is the maximum number of SATA data disks available in this scenario?

Question29: You have just installed a new FAS2650 HA for your customer. You are now configuring the NetApp AutoSupport transport section.
In this scenario, what is the NetApp best practice for this task to allow AutoSupport on Demand (ASOD)?

Question30: Which two default broadcast domains does the system create during cluster initialization? (Choose two.)

Question31: Which tool would help you to verify an installation of an ONTAP cluster?

Question32: A customer buys a new switchless ONTAP 9.1 FAS2650 cluster. You are asked to install the system at the customer's site.
Which three steps are needed to accomplish this task? (Choose three.)

Question33: Your customer has a new FAS2650 HA cluster with ONTAP 9.1 installed. The cluster is connected to two CN1610 switches.
Which two statements describe this installation? (Choose two.)

Question34: You install a new AFF A300 2-node switchless cluster with ONTAP 9.1 at a customer site. Each node has a root aggregate as part of the system configuration.
In this scenario, what is the default disk partitioning called?

Question35: After completing an installation, the customer wants to know how they can manually open a new technical case with NetApp Global Support.
What are three ways to accomplish this task? (Choose three.)